Apple iPod and iPhone (2g, 3g) Dock Interfaces pinout

Apple iPod and iPhone (2g, 3g) Dock Interfaces pinout

connector or cable wiring scheme

Used in 3rd and later generation iPods for charging, connecting to a PC via USB or Firewire, to a stereo via line-out, to a serial device (controlled via the Apple Accessory Protocol). This connector exists in most Apple iPod MP3 players (iPod 3G, 4G, 5G Video, 5.5G Video, Nano (1G, 2G, 3G, 4G), Mini, Classic, Touch, Touch 2G, and iPhone (1G, 3G and 3GS)) Different resistances indicate accessory type: 1kOhm - iPod docking station, beeps when connected 10kOhm - Takes some iPods into photo import mode 68kOhm - makes iPhone 3g send audio through line-out without any messages 500kOhm - related to serial communication / used to enable serial communications Used in Dension Ice Link Plus                  car interface 1MOhm - Belkin auto adaptor, iPod shuts down automatically when power disconnected Connecting pin 21 to ground with a                1MOhm resistor does stop the ipod when power (i.e. Firewire-12V) is cut. Looks to be that when this pin is                grounded it closes a switch so that on loss of power the Ipod shuts off. Dock has the same Resister. Pin Signal Description 1 GND Ground (-), internally connected with Pin 2 on iPod motherboard 2 GND Audio & Video ground (-), internally connected with Pin 2 on iPod motherboard 3 Right Line Out - R (+) (Audio output, right channel) 4 Left Line Out - L(+) (Audio output, left channel) 5 Right In Line In - R (+) 6 Left In Line In - L (+) 8 Video Out Composite video output (only when slideshow active on iPod Photo) 9 S-Video Chrominance output for iPod Color, Photo only 10 S-Video Luminance output for iPod Color, Photo only 11 GND Serial GND 12 Tx ipod sending line, Serial TxD 13 Rx ipod receiving line, Serial RxD 14 RSVD Reserved 15 GND Ground (-), internally connected with pin 16 on iPod motherboard 16 GND USB GND (-), internally connected with pin 15 on iPod motherboard 17 RSVD Reserved 18 3.3V 3.3V Power (+)  Stepped up to provide +5 VDC to USB on iPod Camera Connector. If iPod is put to sleep while Camera Connector is present, +5 VDC at this pin slowly drains back to 0 VDC. 19,20 +12V Firewire Power 12 VDC (+) 21 Accessory Indicator/Serial enable Different resistances indicate accessory type: 1kOhm - iPod docking station, beeps when connected 10kOhm - Takes some iPods into photo import mode 68kOhm - makes iPhone 3g send audio through line-out without any messages 500kOhm - related to serial communication / used to enable serial communications Used in Dension Ice Link Plus car interface 1MOhm - Belkin auto adaptor, iPod shuts down automatically when power disconnected Connecting pin 21 to ground with a 1MOhm resistor does stop the ipod when power (i.e. Firewire-12V) is cut. Looks to be that when this pin is grounded it closes a switch so that on loss of power the Ipod shuts off. Dock has the same Resister. 22 TPA (-) FireWire Data TPA (-) 23 5 VDC (+) USB Power 5 VDC (+) 24 TPA (+) FireWire Data TPA (+) 25 Data (-) USB Data (-) 26 TPB (-) FireWire Data TPB (-) 27 Data (+) USB Data (+)  Pins 25 and 27 may be used in different manner. To force the iPod 5G to charge in any case, when USB Power 5 VDC (pin 23) is fed, 25 must be connected to 5V through a 10kOhm resistor, and 27 must be connected to the Ground (for example: pin 1) with a 10kOhm resistor. iPod 5G can also be forced to charge by attaching the data + and the data - pins to the 5v via a 10k Ohm resistor ( BOTH PINS) and connecting pin 16 to the 5v (ground). (Confirmed working with iPod 5G 20GB) To charge an iPhone 3G / iPod Touch 2nd gen, usb data- (25) should be at 2.8v, usb data+(27) should be at 2.0v. This can be done with a few simple resistors: 33k to +5v (23) and 22k to gnd(16) to obtain 2v and 33k to +5v and 47k to gnd to obtain 2.8v. This is a notification to the iphone that it is connected to the external charger and may drain amps from the usb. 28 TPB (+) FireWire Data TPB (+) 29,30 GND FireWire Ground (-) Back side of dock connector; 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 Pins 1,2 connected on motherboard. Pins 15,16 connected on motherboard. Pins 19,20 connected on motherboard. Pins 29,30 connected on motherboard. If you disassemble the original apple-ipod-dock-connector-cable and look at the connector itself, on the back side, where it is soldered, you can see the number 1 and 30 (e.g. pin 1 and 30). In this description NUMBERING is INVERSED: pin 1 is pin 30 and pin 29 is pin 2, so, don't look at numbers on connector. The remote control, iTalk and other serial devices use Apple Accessory Protocol for communication with iPOD. This protocol was introduced with the 3rd generation iPods, and is also compatible with the 4th generation iPods and mini iPods. The connections uses a standard 8N1 (one startbit 8 data bits 1 Stopbit) serial protocol, 19200 baud (higher rates up to 57600 also possible, but speed faster than 38400 may cause problems with large amounts of data), delay of 12 microseconds inserted between end of the stopbit and the beginning of the next startbit (also working without this delay). Electrical: high +3,3V low 0V default line state: high. Codes used for communication with peripherals are here This device may be connected to the firewire computer port by straight cable (TPB+/-, TPA +/- should be twisted pairs in cable)   iPod Nano 4th Gen no longer will charge from 12 volts on the firwire pins. If you tie pins 25 and 27 together through a 10K ohm resistor while applying +/- 5 volts to pins 23 and 15 (or 16) that it will charge. If you don't tie 25 and 27 together, it won't charge 30 pin iPOD custom connector at the player ( white side up) Connector pinout for: Apple iPod - iPhone dock 30 pin connector used on the dock station for iPod and iPhone. Available in all Apple iPod MP3 player (iPod 1G, 2G, 3G, 4G, 5G and Nano).  oo                   oo usb + -     Vcc - + 뒤집어 보았을때...